latlead.blogg.se - Code composer studio download wont close

Code composer studio download wont close how to#
Code composer studio download wont close update#
Code composer studio download wont close manual#
Code composer studio download wont close software#
Code composer studio download wont close code#

Throughout this document, it will be called the target.

The Board or Device is the hardware that contains one or more devices required for the executable to run.

Throughout this document, the connection will also be called the Debug Probe.

Code composer studio download wont close code#

The connection is the piece of hardware between the host PC that runs CCS, and the device or board where the code is supposed to be executed.

In this mode CCS will not set any breakpoints while the target is running, because this could effect realtime behavior as the target needs to be halted before setting a breakpoint.The physical debugging setup is shown above, with the two main components involved during a debug session: Per default a TI CCS project is in a so-called "non-intrusive" debug mode. Setting a breakpoint while the target is running

Select the desired J-Link script file in the Cpu Properties tab -> J-Link Scriptfile Path (see screenshot below).

Switch to the Advanced tab (see screenshot below).

Select the Cpu properties (see screenshot below).

Switch to the Project Explorer, browse to %PROJECT_NAME% -> targetConfigs and open the active target config with *.ccxml extension (e.g.

Code composer studio download wont close software#

Make sure that J-Link CCS uses at least J-Link software version V6.20g.

Native host interface selection, using the GUI in CCS, is planned for future versions.

The work-around can be used with any J-Link with Ethernet interface.

Code composer studio download wont close how to#

How to use J-Link script files in CCS is described in the article below.įile:JLinkOverrideHostIF.jlinkscript Notes Please find below an example J-Link Script File, which forces the J-Link DLL to open a connection to the J-Link via IP (192.168.104.174). This command string can be passed to the J-Link DLL using the J-Link Script File function InitEMU(). The J-Link DLL allows to override the used host interface using the J-Link Commander String SetHostIF. In current versions of the TI Code Composer Studio (CCS), the host interface to the J-Link (USB / Ethernet) can not be specified in the project settings. The project is now ready to be debugged with J-LinkĬonnecting to a J-Link via Ethernet Problem.In the Advanced tab, additional settings are configurable, e.g.Check the correct target in the list below.In the Connection field choose "SEGGER J-Link Emulator" from the drop down list.View | Target Configuration can be used to find the target configuration file if necessary.Open the target configuration (.ccxml file in the project).In Work With: field: Choose "J-Link Support" from the drop down list.

Code composer studio download wont close update#

Please do not try to download the plugin via your browser from the link above.The plugin is downloadable and installable via the TI CCS update interface only.

In Install/Update select Available Software Sites.

In order to get started with J-Link and CCS, please make sure that latest SEGGER software and documentation pack is installed, which can be downloaded here.Īdding J-Link to Available Software Sites

Now the project is ready to be debugged with J-Link / J-Trace.Īdding J-Link support to older CCS versions.

Make sure that Segger J-Link Emulator is selected as connection type.

Make sure that the proper device is selected.

Open project properties by clicking Project | Properties from the main menu and go to the General tab.

In the following, a short step-by-step tutorial how to configure a Code Composer Studio project to be used with J-Link, is given.

Code composer studio download wont close manual#

A manual update can be triggered via Help -> Check for Updates. The J-Link plugin can be automatically updated as any other Eclipse plugin.

Since TI CCS v7, J-Link is supported out-of-the-box if J-Link support is selected to be added at installation time of CCS.įor more information regarding older versions of CCS: Adding J-Link support to older CCS versions. Please understand that SEGGER does not provide any support for CCS versions earlier than V6.1.3.Īdding J-Link support at installation time

Earlier versions might work but are not guaranteed to do so. 8 Setting a breakpoint while the target is running.5.1 Adding J-Link to Available Software Sites.5 Adding J-Link support to older CCS versions.2 Adding J-Link support at installation time.